LAKESHORE 330 LABVIEW DRIVERS FOR WINDOWS VISTA

LAKESHORE 330 LABVIEW DRIVER DETAILS:

Type: Driver
File Name: lakeshore_330_41014.zip
File Size: 28.9 MB
Rating:
4.63
34 (4.63)
Downloads: 26
Supported systems: Windows 10, Windows 8.1, Windows 7
Price: Free* (*Free Registration Required)

Download Now
LAKESHORE 330 LABVIEW DRIVER



The OR gate on the right receives a TRUE at the start, but waits for the other input before firing, which beats me since the OR condition has lakeshore 330 labview been met.

Instrument Control (GPIB, Serial, VISA, IVI) topics

Net result is not as anticipated. Is there a 3-state object I am just lakeshore 330 labview finding? I discovered that this is due to 64 bit windows?

I also tried using the Watlow driver however if I put the above resource name in for the PC Comms Port in the example included with the driver and try to initialize the lakeshore 330 labview, I get the following error:. The VISA header defines constants for each interface type.

LAKESHORE LABVIEW DRIVER

Attached is a recent test measurement of Thermoluminescence of CsI Tl scintillator, ramping from 50 to K. PID settings are the default of the lakeshore 330 labview no Autotune or Zone settings, and no manual tuning of any kind.

The upper graph shows the ramp where the temperature stayed reasonably close to setpoint and lakeshore 330 labview versus time, while the lower graph shows counts per degree K increase of temperature. I would advise doing some experiments with the Ramp function and see how it goes.

Lakeshore data sensor vi is not working - NI Community - National Instruments

Turn on suggestions. Message 4 of 7. General advice lakeshore 330 labview I don't know your system specs: 1 use a diode temperature sensor not thermocouple ; calibrated values loaded into Lakeshore preferred. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Goto the examples finder type and there you find an vi that does all the work for you. I have found advice on how to turn it on, but I don't know what I need to install so that it is available. This means that i will have a PLC powerline modem connected lakeshore 330 labview my laptop and then i need to control my devices from there.

  • Labview software for Lakeshore temperature controller - NI Community - National Instruments
  • Instrument Control (GPIB, Serial, VISA, IVI) topics
  • Erratic behavior Lakeshore - NI Community - National Instruments
  • Lake Shore Cryotronics 330
  • Instrument Control (GPIB, Serial, VISA, IVI) topics
  • Instrument Control (GPIB, Serial, VISA, IVI)

It will listen and respond when addressed but never be the CIC. My codes is on a stand-alone computer and I don't want lakeshore 330 labview re-write it, so I will use the example code and describe mine.

Good so far. However, on the next loop the VISA Wait On Event should time out if not addressed - it does not time out, it plows on through as if lakeshore 330 labview listen event has occurred.

Lake Shore Cryotronics 330 Controller

I know we have to manually tune it but is there any other method of doing it. I'm actually working right now on a setup for thermoluminescence using a Lakeshore I haven't done any PID tuning or zone lakeshore 330 labview yet, so I can't help that much, but I did notice that at least with the you have to do more than load the zone table, you also have to set the "mode" to "zone" rather than "closed-loop" in the "Configure Heater Output.

Your model may be different, of course. Message 2 of Actually, it is much easier to fix the first, which uses Shift Registers instead of Lakeshore 330 labview Loops I always have trouble with Feedback Loops, but Shift Registers seems almost intuitive to me. I would like lakeshore 330 labview buy the necessary Labview driver set along with Labview software for the temperature controller.

LAKESHORE 330 LABVIEW WINDOWS 8.1 DRIVER

This doesn't sound like a LabVIEW problem to me, as the lakeshore 330 labview should only be adjusting the set-point and heater range. If you think the drivers for the will work with the then you can post a request in the Version Conversion Board to have the drivers downconverted to your LabVIEW version.

lakeshore 330 labview How can I get this VI to read from my temperature controller? I found some documentation of conflicts this device has when used with other devices.Drivers>>Lake Shore Cryotronics Instrument Model: LabVIEW, Plug and Play (project-style), IEEE (GPIB), Serial, None, Yes,Go To. Download lsci, a LabVIEW IEEE (GPIB),Serial Plug and Play (project- style) instrument driver for a Auto-Tuning Temperature Controller lakeshore 330 labview.

Relevant Posts